Rev. 6 — 3 December Product data sheet. Table 1. Ordering information. Type number Package. Temperature range Name. Description. Version. when gated with the Clock of the HC .. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in. HC datasheet, HC circuit, HC data sheet: TI – DUAL 4-BIT BINARY COUNTERS,alldatasheet, datasheet, Datasheet search site for Electronic.

Author: Vujar Shacage
Country: Nepal
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 December 2008
Pages: 288
PDF File Size: 12.69 Mb
ePub File Size: 3.99 Mb
ISBN: 376-2-94356-204-7
Downloads: 83210
Price: Free* [*Free Regsitration Required]
Uploader: Dogis

This can be continued datashset any number of flip-flops, each one of which will represent a binary digit. Each of the outputs goes positive during its time interval, remaining low otherwise. Wire up this circuit and test it.

The alternative, a numerical or digital display, makes a clock fully electronic, and is easy to realize.

Synchronous counters are not afflicted by the obvious glitches of ripple counters, but they datashret still suffer from glitch problems of a more subtle nature. The output misnamed Carry Out, CO, is not a carry-out, but has a very definite purpose. It is also possible to clock the higher counter and reset at any value of N.

Hc393 datasheet pdf

This can be done for as many counters as desired. There are 10 states, so this is a decimal counter by nature, and the states can be assigned to the integers as shown.

Synchronous binary counters require a lot of logic, and they are not made from discrete components, except as a school exercise. These distinctions are often used with counters, and are quite important in making a design.

Some method must be available to set the clock. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. This requires a slow change at the minutes level, as well as a rapid change for large alterations. Find out how much the clock gains or loses in 24 hours, perhaps by comparison with WWV.


The decodes could also drive relays to activate any kind of display. A 4-Nixie display will draw no more than 8 mA. Search Forums Recent Posts.

HC Datasheet(PDF) – TI store

When that time arrives, the seconds counter is again enabled. By cascading two modulo counters and a modulo counter, you now have an electronic escapement for a clock, which is dstasheet by a 1. The hours and minutes are set at some convenient time in the near future. Except for a common clear control, these two sections are independent, and can be used separately.

Such equipment includes, without limitation, allmedical devices identified by the U. The outputs go nearly to the supply rails, but can furnish only less than a mA.

This is the Johnson counter that is based on a shift register of N stages. A shift register is a series of flip-flops with each output Q connected to the next input D, and the clock inputs connected together. Connect the ENP’s together and tie them high. The escapement is represented by the oscillator, hd393 to the mechanical oscillators of a mechanical clock. Finally, there are synchronous up-down counters like the 74LSLS, whose uses are more specialized.

CD74HCTE datasheet & applicatoin notes – Datasheet Archive

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications thatinclude the TI product s identified in such TI Resource. Alternatively, a lot of NE-2’s could be assembled into a neon display. The 74HC, a 7-stage ripple counter, can be used to this purpose, as shown in the diagram at the left. Note that S of the master cannot be high when J is low, nor R high when K is low.


The clock cannot be regulated experiments with pulling datasheeet crystal oscillator will be madealthough its rate is constant and can be determined by observation, so that the correct time can always datashwet found. If synchronous counters are used, it would be possible to preload the counters to any value, perhaps selected by thumbwheels, and then to start the clock at the proper moment.

The count 23 59 will dqtasheet followed by 24 60, and then both counters will be reset to 00 The slaves have stabilized while E has been high, so this will be the case.

Be sure to use despiking capacitors on the power supply, since switching transients can be considerable. Any dimension in brackets or parenthesis are for reference only. Discussion in ‘General Electronics Discussion’ started by dataseet, Jun 20, The simplest way is ripple cascading, which is appropriate for the 74LS90 family.

So you’ve already worked out that you want to divide the 5 kHz frequency by ? Such accuracy in a mechanical watch comes at a very great price, datashret it is available at all.

If you are building a clock, you will need two of hc93 counters, one to count seconds up to minutes, the other to count minutes up to hours.

It divides the input frequency by 2, which it is frequently called upon to do. The chip was specifically designed with this in mind. Try this circuit, and you will find that it counts from 0 up to 8, and then returns to datasyeet.

Electronic clocks are analogous to mechanical clocks.