Aqualis Caleo high-temperature air-to-water heat pumps are specially .. As part of its policy of continual product improvement, CIAT reserves the right to make. AQUACIAT CALEO: the refurbishment solution suitable for both large homes and as those offered by CIAT´s Aqualis Caleo product – were limited to 20kw. Consult CIAT’s NAN brochure on MedicalExpo. Aqualis 2’s added benefits The Aqualis 2 heat pump from CIAT is the key AGEO CALEO – NAD.
|Published (Last):||13 May 2005|
|PDF File Size:||17.49 Mb|
|ePub File Size:||19.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Particularly suited to renovations, the unit is designed to be connected to an optional mixing tank with multiple connections that supplies water to high-temperature radiators.
In hot water production mode heating, pool, frost protection or domestic hot water modes: Walls can increase noise levels considerably and reflect noise in various directions. English Installation D e u t s ch – Settings stored in memory for two hours following a power cut – Blue backlit digital display – Maximum dimensions: If your system is fitted with cakeo optional electric heater, install the valve near it.
Access to level-2 installer settings For further information on reading and programming the terminal, refer to the manual provided with it. The fault type appears on the terminal LCD.
NAN – CIAT – PDF Catalogs | Technical Documentation
Italiano 2 – Turn the dial on the terminal unit to the desired operating mode. To access the settings, do as follows: Electrical connection tightness check Outdoor coil cleaning Control check Differential water pressure switch Status of liquid sight glass and leak detection 44 5.
Italiano 3- Using litmus paper or a pH meter, check the pH obtained. R L Always comply with the appropriate bend radius. The Online Industrial Exhibition. Go to following day Time and day adjustment, unit off Not used Not used Not used Not used Not used Not used Not used Not used Four-cursor display Four-cursor display —————————- Off and reset mode permanent fault —————————- Frost protection mode Unit authorised to produce hot water Go to Comfort mode, Economy mode then Programmed mode.
Do not tighten these screws to a torque of greater than 13 Nm. Please contact your boiler manufacturer to find out whether the heating source is compatible with Microconnect control. To keep your unit running smoothly and to benefit from the warranty, take out a maintenance contract with your installer or an approved maintenance company. Its compact footprint makes it particularly suited for installation as a boiler backup on existing systems.
It is not necessary to add glycol to your system if aquqlis are absolutely sure that there is no risk of freezing temperatures in your area. However, as soon as you begin designing your system, you should take into consideration the outdoor environment to estimate the radiated noise and the building type to estimate the noise transmitted through the air and by solid materials vibrations.
The protective covers may be removed in order to change the circulator speed or reach the release aqualid. Control is carried out on interstage differential P Medium capacity air-to-water heat pump for “high temperature” heating caoeo. D e u t s ch Connection diagrams schematic diagrams Terminal display when the outdoor temperature is less than P9 and only the boiler is authorised. AWG 16 to 28; or 0. The valve does not need to be separated from the heater by a shut-off valve.
Remove the top as shown in Figure 1 and make a connection xqualis terminal block J1 on the PSU board the one with the contactor.
The room temperature is managed by the Microconnect terminal. English Fig 1 1 Remove the middle screw rear of unit 2 Detach both ends as shown in cist 3 Remove of the top by sliding it toward the rear D e u t s ch – The characteristics of the mains supply must be identical to those on the data plate. D e u t s ch Installing the filter Filter installation d!
IP 30 – Operating temperature limits: Particularly suited to renovations, the unit is designed to be connected to an optional mixing tank with multiple connections that supplies water to high-temperature radiators. It may be necessary to use them when starting the unit or when turning it off for extended periods of time. As the hoses are insulated, bend them at sufficiently wide angles calfo avoid pinching the inner tube and restricting the flow of water.
Faults are stored in memory during power cuts and the fault relay is stuck in a particular position. If the direction of rotation is wrong: Make sure the terminals are securely tightened. Easy-to-use microprocessor-based MicroConnect remote control unit with many self-regulating functions.
Serves as a boiler backup in large homes and multi-residential buildings as well as businesses, hotels and healthcare facilities.
Stage-1 electric auxiliary unit operation Indicator 4: Depending on the geographic location and the type of mains network buried or overheadyou may have to install a lightning rod. Turn the terminal dial to one of the following positions: Insulate the filter or install it indoors protect claeo freezing temperatures.
The predominant problem with outdoor units is disturbance caused to the neighbourhood because of noise. Moreover, a d3 fault water flow rate fault must not prevent the boiler from operating.
Classic air conditioning unit Wall-mounted fan coil unit Hot water heater. This can be done by opening the manual bleed valve located under the unit cover when turning the unit on or by installing a section of the water line and an automatic bleed valve over the unit.
Fully encased in a housing constructed of coated metal panels that can be detached for outdoor installation.
Compressor operation Indicator 5: